Printable View
Nearly every night, there is a 1 or 2 minute call in the logs to DirecTV (8666858469) at about 03:00. I understand that my receiver is probably sending usage stats or something to the mother ship.
Is it doing this each night because it is failing and retrying, or is this normal? I am thinking about unplugging the phone line from the receiver!
Per http://www.dslreports.com/forum/r188...ecTV-questions
Quote:
The phone line only needs to be connected to the DirecTV branded units if you want to order PPV using the receiver and remote. No loss without the phone line - order from the website. I *think* the DirecTiVO units need a phone line all the time (to update the channel guide).
Do you have an older DirecTV TIVO or is it one of the newer boxes? TIVO modems are not compatible with most all VOIP providers, the new models work fine (I have 5 DirecTV HD-DVR's). If it's a TiVo the number you are calling may also now be non-working. You would need to update local numbers. Other then that it doesn't need a phoneline anyway but depending on which model you have it may nag you daily. Mine are all connected to my router so all calls are done over the net.Quote:
Originally Posted by abward
usa2k, ok I will unplug the phone line on it...We never use PPV. Thanks.
MisterEd, it is an HR-21, HD DVR receiver.
Since it is connected via Ethernet to the mother ship, I am not sure why it is trying to call via phone.
It shouldn't be calling unless there is a PPV on your card that never got sent up from before you went network. Also you might want to call DirecTV and tell them to confirm that your receiver is showing as internet connected on your account (IPPV box enabled).Quote:
Originally Posted by abward
It's possible it could be trying to send useage data. You can opt out from that in your online account under "Privacy." None of mine have ever dialed out even though they all have phone lines for caller-ID and are also networked.
Well that is interesting...I did not know about the privacy setting. I set it to opt-out and we will see if that fixes it. I would rather not lose the caller-id feature.
I will try the IPPV next. I pretty sure we have never watched a PPV.
This is a known problem for some Directv users including myself. It's indicative of failed modem calls through your ATA device. Modem calls through VOIP is basically unreliable, they usually either work or they don't.
For unknown reasons some HD DVR's simply refuse to stop dialing out even with it network connected. Your situation is similar to mine with the exception of the phone number being used. The 866-685-8469 number appears to be the one that is used to report viewing habits. If you follow MisterEd's advice and change the Privacy setting to "opt out" in your Directv account, this should eliminate the dial out problem. If it doesn't fix it or it dials out another number 800-531-5602 (this one is used to report PPV purchases), then you will need to add the *99 dial out prefix to the phone number in your HR21. Hopefully, this will get the modem to work and will maintain the great caller ID feature built into the DVR.
Basically, the *99 command temporarily changes some settings in the ATA to allow it work with a modem. After the call is complete, the default settings are restored in the ATA. This is applicable to the PAP2T and other Linksys ATA's, but am unsure whether it works with the RT31P2. Just give it a try and see if it works or not. The link below contains more information and has another link in the thread on how to add the *99 prefix in the HR21.
http://www.dslreports.com/forum/r231...ecTV-receivers
The opt-out did not prevent the call this morning. I will try a "*99," prefix. Thanks tritch.
If *99 doesn't work don't give up. It could take up to 1 week for the "opt out" to complete.Quote:
Originally Posted by abward
Ok, since it did not work...it dialed last night.
Also, I was thinking that I have an H20-600 upstairs too. Maybe it is trying to dial. So, I will unplug the phone on it and see what happens tomorrow.
Call DirecTV and tell them you smell smoke from your H20-600 and it is getting very hot. :) There was a national callback on the H20-600's last year (but it has since ended) for overheating. There should be a stamp on the bottom with a code on it (ECO 1 or ECO 2 or no code at all). If it's ECO 2 it's been "fixed" if the code is ECO 1 or there is no code it's in the group that was called back. They used to replace them automatically but now you need to tell them it's very hot to the touch and smells like it's "burning up."Quote:
Originally Posted by abward
You might want to unplug everyhting that is phone connected to your ATA except the HD-DVR and 1 phone and see what happens overnight. You might also run the "system test" which does a test dial as the last test and see if it passes on both receivers.
(I was a DirecTV tech support & cust service trainer for a few years for a local private callcenter which handled only mdu type properties :) )
Yes, I am aware of the recall. Mine is an ECO 2, so I don't qualify. It runs warm, so I won't mind it too much when it finally does break. I finally go around to unplugging the H20-600 phone line today, so I will see what happens tomorrow.
FYI, it looks like the H20-600 is doing it, since I unplugged the phone line to it last night and it did not dial out in the log.
I did some Googling and it appears that there is no way to change the dial string (to prefix a *99,) on it.