2 instances of my number

**usa2k** · 05-10-2008 08:53 PM

Originally Posted by VOIPoTim

We run on ALL ports in the range of 5060-5080. If you already have something in 5060, register to us using an alternate port.

I tried my ZyXel phone as a second existence of my VOIPo number.
It registered "sip:313432xxxx@192.168.0.xxx:5070"
But now it looks like my Grandstream won't show in vPanel

Initially I get a dial tone

On the ZyXel I get a busy tone when I try to call.

On the ZyXel I get "Comedian mail" greeting when I type 123

I can call out from the Grandstream and calls go straight to voicemail.

**usa2k** · 05-10-2008 09:01 PM

I rebooted the Grandstream and they both show now
"sip:313432xxxx@67.149.75.xxx:33496"
Incoming works to the Grandstream now.

**usa2k** · 05-10-2008 09:12 PM

Main config info for ZyXel

**chpalmer** · 05-10-2008 09:12 PM

Look a bit later...

Some ATA's have a "Initial Unregister" that they send to the server that wipes it clean of any other registrations.

I dont know if its only at boot or at every registration attempt.

Might be what happened to you...

**usa2k** · 05-10-2008 09:14 PM

Perhaps you will use MAC IDs? (Limit/control multiple instances.)
And have a place to register such an ID.
Then VM can work the same.

Still not sure about dialing out?
I can gget to VM by 123, then my number and my password.
Dialing out always fails.
codeblue.voipo.com:5060 seems necessary to register
even though the ATA can be codeblue.voipo.com:5070 (See image on earlier post.)

**usa2k** · 05-11-2008 08:46 AM

Both Grandstream and ZyXel show they are registered

Only the Grandstream can place calls.
The ZyXel is not interfering with incoming for Grandstream.

Both show registered on vPanel.

**usa2k** · 05-11-2008 09:10 AM

BTW, I have P8 forwarded to VOIPo number.

It looks confusing to have the P8 phone still as one of my two lines, because P8 still rings once or twice even though VOIPo is ringing (And that is P8's forward option - not simul-ring.) So I am leaving P8 unconnected to any phone.

Forwarding should not interfere with my P8 LNP to VOIPo. It never affected Vonage to P8 ...

VOIPoDanielC · 05-12-2008 01:12 PM

In a "double device" scenario, it isn't always sent to both devices on incoming calls.

The "last" device that sent a register for that period gets precedence for anything.

You may want to disable to unregister before register feature/s if they exist on the ATA.

You can also do "make outbound calls without registering" so it will still attempt the outbound call and should make it if the outbound proxy information is correct.

**usa2k** · 05-12-2008 05:12 PM

Really outbound is all I am looking for. The odds of using the second line is rare, but it is just comforting to have the option.

When I had 5060 before, it worked outbound - I should try that again. It seemed to mess-up the inbound to the Grandstream. I've got a busy night, and I am out of town tomorrow, but I will have time to play Wednesday.

**usa2k** · 05-14-2008 05:19 PM

I had issues trying this today, but had more success using port 5061.
I put in a help request for no outbound audio when getting an incoming call.
VOIPo support had a look and it all seems good now.

5061 was working good at one point and I may have complicated things by trying a few other ports. vPanel was stacked up with device registration lines. So it could have been my own problem.

Bottom line - all is good

The Grandstream is for in/out
The ZyXel is for out only if ever needed.
I route the in to the other phone port not connected. (ZyXel lets you decide which/both ports ring.)

Oh ... 123 for VM is working great from either line

(No Comedian Mail greeting!)